How do you lay floor tiles in a kitchen? does it matter whereabouts in the room you start?
Question:
Answers:
Best to find the centre horizontal line then work outwards..
Always start at the doorway...it is the first thing you notice when you enter .
Tess
Find the centre point of the room and draw a cross there - place 4 tiles so that they meet at the corners at that centre point and radiate out from there.
yes it does matter you begin at the far end corner or wall opposite to the door and finish at the door so you walk out with disturbing the tiles laid by walking on them as you work you way out.
Start in the middle of the room. You will find that the walls are not at 90 degrees to each other so it will make a difference.
you need to start in th middle mate with your first tile just measure it out and slap em down then you can put your feet up and have a beer.
The following website tells you everything that you want to know about laying floor tiles in a kitchen
http://www.ceramic-tile.com/tileman.cfm?...
I hope that this answers your question.
start from the middle and work outwards they should b staggered
depends on the layout of the kitchen and what you like of course. the best way is starting at the center of the room that way your cuts will be at the walls and not in the center of the floor but if you have a door in the corner of the kitchen you can start there and work your way from the wall/door out to the other side .
What do you intend laying them on? And you didn't say if they were vinyl or ceramic
If the surface is at all uneven, it is usually a good idea to lay the tiles on hardboard or ply.
If you are laying cermaics you will need to use spacers and finish by grouting them.
The professionals do as already advised and mark the centre of the room in both directions, putting the first 4 tiles right in the centre first.
This way does mean that you will probably have to cut every single tile at the end, right up against the walls, but it will give you a very tidy border with a professional looking finish
Yes it matters where you start. Depending on the design and area configuration, you start in the middle of the floor and work your way to the walls, or start right where you come into the room, so areas where you trim the tiles are not as exposed.
for the best effect start in the middle and run your tiles outward. This will not only give you a symmetrical floor but also easier cuts around the walls
It does matter, take your time in deciding this. With my years of experiance in installation, I always use the countertops as a reference. For example, if you start square off the interior wall, it may not be square with the cabinets. No home is square, you always install for visual. If your tiles are not square with the counters, you will notice...As a beginner, I would take the time to dry lay the tile. I know the cost of professional installation is expensive, but sometimes it's worth it. If you have any questions, please feel free to e-mail me.
yes it does try to find centre of room check that cuts on walls are not going to be too small take your time go to library and get book on subject or get a floor layer in very hard to explain on here floorlayer for 40 odd years
start in the center.
I got this tip from a professional tiler who does prestige work.
Lay square tiles on the DIAGONAL, and arrange the starting so that the "Cuts" are symetrically placed around the room. By so doing there are no slivers of tiles on one or two walls. THEY ARE EQUIDISTANT
You are supposed to begin in the middle of the room, that way the cut pieces will be against the walls.
First let me say starting in the middle of the floor is the home depot do it yourself layout.As a professional tile installer I almost never start at room center.If it is just the kitchen always start full tiles where your tile is going to meet the carpet.If there is another entrance layout for full tiles of that aswell then measure two tile rows from both starting points and snap crossing lines.Then check for square using a framing square or the prefered method of measuring 3 for 5 for square.If your out of square measure from walls and make the best adjustment for the layout.Install tile.Remember full tiles at entrances always looks better than a center installed floor and that is the way proffessionals install centered = home depot.
start from the centre outwards best way ive found ;-)
Hello i would be happy to help just go to my website (below) and go to the contacts page and there will be a form ask for help and you will be given almost everything you need to know about tiling on the next day
lay tiles down dry first and then lay when happy with which way your happy with doing it there is know real way of doing it it,s just everybody has a preference.
my method,
depends on size of floor area and also time limit i would lay down dry along the longest run that is furthest away and work back to door entrance(only one door in an out then people cant step on freshly layed tiles) remember your cuts for corners and utilities you need them to be spot on or it looks unsightly. good luck
here is what i always do make a cross with just laying the tiles out on the floor straight out of the box, ( no thin-set) looke to see where your cut pieces will end up and how much. always try to get the cut pieces on one side and try to make them against the cabinets so people never notice, the dry run will just be a big cross in the room
More Related Questions & Answers...