Wallpaper! How can I hang it so that the joins don't show? Help needed! Many thanks!?
Question:
Answers:
If the seams show right after you put up the paper it means it isn't straight and plumb...If they begin to show after the paper drys out it means you stretched the paper when putting it up.After the paper drys it will return to the unstretched area...
1. Start out with a clean straight piece of paper..Using a plumb bob sometimes tells you where straight up and down really is.
Take note of the pattern and find an identifiable feature ...
2. Sheet #2...Find the identifying feature and cut the sheet (Cut it so you have extra paper on top and at the floor.). Put it up on the wall dry so you are sure its correct..
3. Book your paper in the tub.
4. When you are ready take the paper and align the pattern...Then i usually go to the top of the paper and stick a razor blade or thin scissors in the paper between the ceiling and the trim work.This will hold up the weight of the paper..Then I pull the paper OUT from the wall and lay it down perfectly straight without having to hold up its weight...
And I never use a roller...I use a plastic straight edge to push out the excess glue and just wipe it up with a wet towel.
The reason you get the seam showing is because while trying to drag the paper over to the seam you are stretching the paper.The motion must be lifting out from the wall and straight back to the wall...
Oh yea.
40 yrs experience in doing sh*t without any money...
Edit:
I do all of my wallpapering in the middle of the night alone.That way I can curse up a storm...
Plus no one can see my mistakes untill I get a chance to fix them...
Um, don't overlap it adn make sur eyou match up the patterns
wallpaper is designed so it can be hung without the joins showing...
Make sure there is no gap between the sheets, and buy a wallpaper roller from the DIY store. Made of plasic, about 1" wide. You roll it over the length of the joint and it squeezes all of the adhesive out so that both sheets are perfectly flat against the wall.
(I'm not a professional though, just a DIY'er).
dont overlap & use a joint roller
First make sure the first piece is plumb. Line up the pattern on the paper and apply. Do not overlap. Use a joint roller for the edges.
make sure you paste right up to the edges and then butt the two bits of paper up next to each other. then with a soft DRY brush smooth out the wall paper.
p.s if there is a pattern make sure it mtches by moving it up or down it will eventually match
most prepasted wallpaper after a day or so of being hung will draw up just a little at the seams so it does not matter how perfect you join the edges,this usually happens.
if you really want it perfect some people will paint the wall the color of the wallpaper so you do not see the seams as well and that is a good idea if your a perfectionist...
another idea is to buy some wallpaper markers and after the wallpaper has been hung for a day go back with the markers and fill in the seams..
if you have the right amount of paste on the paper, you should be able to gently slide the paper up to the bit already up just enough touching the edges. Its trickly to start off with, but start in a corner that doesn't get looked at as much, so by the time you finish you should have it perfect.
The best way is to cut the edges with a razor blade.Make sure you match the pattern.You must have a straight edge,like go to a place that has a long straight edge that you can use.Fold the section into three parts wet of course.With
glue on them.Put straight edge along the the edge of paper.cut with razor blade.Put on wall,prep it of coarse.Use seam roller to get eccess glue out.
Make sure to use plenty of paste especially along the edges. Leave on pasting table to allow paste to adhere,couple of Min's, then start from top and line up next to previous strip. Slide into place, do not overlap. Use a cloth to push out all the air from the middle out and finish with a small roller that is made to seal edges. These are cheap from wallpaper suppliers or DIY stores. Don't forget to allow for the pattern, on the label it will tell you the measurement for this. Another tip when buying paper always make sure they are the same batch number or you could get a difference in the colour...Good Luck hope this helps.
paste the paper let it soak ie:- paste 3 lengths before starting to hang butt joint the paper on no acount overlap
Use a seam roller on the joint unless it is an embossed paper as the roller will flatten the embossment
use a bristle wallpaper brush to flatten the paper to the wall or a sponge dont forget to make sure that the paste is wiped off the join if any is on the paper
In addition to what has gone before, it is important that you begin papering the room at the window (or at least in the corner nearest) as any overlap, viewed from the door will be less obvious. Always paper away from the window otherwise the joins are facing the door!
Yep! as Duffer suggests, always start at the far end of a room & work towards the entrance it gives a much better appearance if joints slightly overlap due to pattern positioning.
Also be very carefull of paste on the surface keep a bucket of clean water and a sponge handy & wipe the joins gently downwards after each strip & change the water regularly using a seam roller does tend to squeeze excess paste onto the surface so clean the roller after each run as well..best of luck! Smiffy
More Related Questions & Answers...